When.com Web Search

Search results

  1. Results From The WOW.Com Content Network
  2. List of drill and tap sizes - Wikipedia

    en.wikipedia.org/wiki/List_of_drill_and_tap_sizes

    Example (inch, fine): For 7 ⁄ 16-20 (same diameter as the previous example, but this time with 20 threads per inch, which is considered fine), 0.437 in × 0.90 = 0.393 in (i.e., if the threads are to be fine, then a slightly larger diameter drill bit should be used before tapping the hole for the screw).

  3. Unified Thread Standard - Wikipedia

    en.wikipedia.org/wiki/Unified_Thread_Standard

    The minor diameter D min ... For diameters smaller than ⁠ 1 / 4 ⁠ inch, the diameter is indicated by an integer number ... ⁠ 1 / 4 ⁠ ″ 0.2500 6.3500: 20: 0 ...

  4. List of thread standards - Wikipedia

    en.wikipedia.org/wiki/List_of_thread_standards

    ANSI B1.20.3-1976 (R2013) Dryseal Pipe Threads (Inch) Pipe Thread Form ASME B1.20.7-1991 (R2013) Hose Coupling Screw Threads - Inch: Pipe Thread Form ASME B1.21M-1997 (R2013) Metric Screw Threads - MJ Profile: V Thread Form BS 84: Tables of BS Whitworth, BS Fine and BS Pipe Threads: V Thread Form (55°) 14 ″-20 BSW ISO 68-1:1998

  5. ISO metric screw thread - Wikipedia

    en.wikipedia.org/wiki/ISO_metric_screw_thread

    A metric ISO screw thread is designated by the letter M followed by the value of the nominal diameter D (the maximum thread diameter) and the pitch P, both expressed in millimetres and separated by a dash or sometimes the multiplication sign, × (e.g. M8-1.25 or M8×1.25). If the pitch is the normally used "coarse" pitch listed in ISO 261 or ...

  6. Screw thread - Wikipedia

    en.wikipedia.org/wiki/Screw_thread

    The common V-thread standards (ISO 261 and Unified Thread Standard) include a coarse pitch and a fine pitch for each major diameter. For example, 1 ⁄ 2-13 belongs to the UNC series (Unified National Coarse) and 1 ⁄ 2-20 belongs to the UNF series (Unified National Fine). Similarly, M10 (10 mm nominal outer diameter) as per ISO 261 has a ...

  7. Drill bit sizes - Wikipedia

    en.wikipedia.org/wiki/Drill_bit_sizes

    So a 1 / 2 in (12.7 mm) diameter drill will be able to drill a hole 4 + 1 / 2 in (114.3 mm) deep, since it is 9 times the diameter in length. A 1 / 8 in (3.175 mm) diameter drill can drill a hole 1 + 5 / 8 in (41.275 mm) deep, since it is 13 times the diameter in flute length. [3]

  8. Preferred metric sizes - Wikipedia

    en.wikipedia.org/wiki/Preferred_metric_sizes

    Each nominal diameter specifies different ID minimum and maximum values. The nominal size is a Renard series. Nominal Size ID ... 1 ⁄ 2: DN 20 26.9 3 ⁄ 4: DN 25

  9. Trapezoidal thread form - Wikipedia

    en.wikipedia.org/wiki/Trapezoidal_thread_form

    A minimum root-crest clearance of 0.01 in (0.25 mm) (diametral) between opposing threads with 10 tpi (threads-per-inch) or fewer, and 0.005 in (0.13 mm) for finer pitches. (This is also true for the minor diameters of the Centralizing Acme thread, though not its major diameters, where the allowance is made less than the PD allowance.)