Ad
related to: 1 liter water to kg conversion formula ph- Dissolved Oxygen
High performance, reliable
DO sensors to monitor the process
- Revolutionary Technology
Intelligent Sensor Management
White papers, guides & more
- Sodium & Silica Analyzers
Reliable, on-line analyzers with
automatic calibration
- Pharmaceutical
Reliable solutions for conductivity
and TOC measurements
- Contact Us
Question about measurements?
Call or contact us via email
- Brochure Gas Analysis
Check out our free publications!
More about parameters/applications
- Dissolved Oxygen
Search results
Results From The WOW.Com Content Network
It is measured by titrating the solution with an acid such as HCl until its pH changes abruptly, or it reaches a known endpoint where that happens. Alkalinity is expressed in units of concentration, such as meq/L (milliequivalents per liter), μeq/kg (microequivalents per kilogram), or mg/L CaCO 3 (milligrams per liter of calcium carbonate). [3]
At 15.6 °C (60.1 °F), the density of a saturated solution is 0.88 g/ml; it contains 35.6% ammonia by mass, 308 grams of ammonia per litre of solution, and has a molarity of approximately 18 mol/L. At higher temperatures, the molarity of the saturated solution decreases and the density increases. [ 8 ]
Baumé degrees (light) was calibrated with 0 °Bé (light) being the density of 10% NaCl in water by mass and 10 °Bé (light) set to the density of water. Consider, at near room temperature: +100 °Bé (specific gravity, 3.325) would be among the densest fluids known (except some liquid metals), such as diiodomethane .
V eq is the volume of titrant (ml) consumed by the crude oil sample and 1 ml of spiking solution at the equivalent point, b eq is the volume of titrant (ml) consumed by 1 ml of spiking solution at the equivalent point, 56.1 g/mol is the molecular weight of KOH, W oil is the mass of the sample in grams. The normality (N) of titrant is calculated as:
m(NaCl) = 2 mol/L × 0.1 L × 58 g/mol = 11.6 g. To create the solution, 11.6 g NaCl is placed in a volumetric flask, dissolved in some water, then followed by the addition of more water until the total volume reaches 100 mL. The density of water is approximately 1000 g/L and its molar mass is 18.02 g/mol (or 1/18.02 = 0.055 mol/g). Therefore ...
Hence 1 L ≡ 0.001 m 3 ≡ 1000 cm 3; and 1 m 3 (i.e. a cubic metre, which is the SI unit for volume) is exactly 1000 L. From 1901 to 1964, the litre was defined as the volume of one kilogram of pure water at maximum density (+3.98 °C) [ citation needed ] and standard pressure .
If the concentration of a sulfuric acid solution is c(H 2 SO 4) = 1 mol/L, then its normality is 2 N. It can also be called a "2 normal" solution. It can also be called a "2 normal" solution. Similarly, for a solution with c (H 3 PO 4 ) = 1 mol/L, the normality is 3 N because phosphoric acid contains 3 acidic H atoms.
Liquid water has a density of approximately 1 g/cm 3 (1 g/mL). Thus 100 mL of water is equal to approximately 100 g. Thus 100 mL of water is equal to approximately 100 g. Therefore, a solution with 1 g of solute dissolved in final volume of 100 mL aqueous solution may also be considered 1% m/m (1 g solute in 99 g water).