When.com Web Search

  1. Ad

    related to: 2.5 inches to diameter

Search results

  1. Results From The WOW.Com Content Network
  2. List of disk drive form factors - Wikipedia

    en.wikipedia.org/wiki/List_of_disk_drive_form...

    8-, 5.25-, 3.5-, 2.5-, 1.8- and 1-inch HDDs, together with a ruler to show the length of platters and read-write heads A newer 2.5-inch (63.5 mm) 6,495 MB HDD compared to an older 5.25-inch full-height 110 MB HDD. IBM's first hard drive, the IBM 350, used a stack of fifty 24-inch platters and was of a size comparable to two large refrigerators.

  3. French catheter scale - Wikipedia

    en.wikipedia.org/wiki/French_catheter_scale

    The Charrière is measured by the ''outer'' diameter, and is defined as 1 Fr = 1/3 mm, and thus 1 mm = 3 Fr; therefore the diameter of a round catheter in millimetres can be determined by dividing the French size by 3. [2] The French units roughly correspond to the outer circumference of the catheter (see table below).

  4. Ring size - Wikipedia

    en.wikipedia.org/wiki/Ring_size

    In the United States, Canada, and Mexico, ring sizes are specified using a numerical scale with 1 ⁄ 4 steps, where whole sizes differ by 0.032 inches (0.81 mm) of internal diameter, equivalent to 0.1005 inches (2.55 mm) of internal circumference.

  5. Drive bay - Wikipedia

    en.wikipedia.org/wiki/Drive_bay

    For 2.5-inch bays, actual dimensions are 2 + 3 ⁄ 4 inches (69.9 mm) wide, between 5 millimetres (0.20 in) and 3 ⁄ 4 inch (19.1 mm) high, and 3.955 inches (100.5 mm) deep. However, most laptops have drive bays smaller than the 15 mm specification. 2.5-inch hard drives may range from 7 mm to 15 mm in height.

  6. Computer case screws - Wikipedia

    en.wikipedia.org/wiki/Computer_case_screws

    The #6-32 UNC screw has a thread pitch of 1/32 in (0.031250 inches (0.7938 mm)). The #6-32 UNC is a UTS screw specifying a major thread diameter of #6 which is defined as 0.1380 inches (3.51 mm); and 32 tpi (threads per inch) which equates to a thread pitch of 0.031250 inches (0.7938 mm). The optional UNC specification indicates the standard ...

  7. Nominal Pipe Size - Wikipedia

    en.wikipedia.org/wiki/Nominal_Pipe_Size

    Nominal Pipe Size (NPS) is a North American set of standard sizes for pipes used for high or low pressures and temperatures. [1] " Nominal" refers to pipe in non-specific terms and identifies the diameter of the hole with a non-dimensional number (for example – 2-inch nominal steel pipe" consists of many varieties of steel pipe with the only criterion being a 2.375-inch (60.3 mm) outside ...

  8. List of floppy disk formats - Wikipedia

    en.wikipedia.org/wiki/List_of_floppy_disk_formats

    Used only in Tandy Portable Disk Drive 2 5 1 ⁄ 4 inch Double 1 35 18 256 ... 8 inch single 1 50 8 3,500 b: hard 1.4 Mb [15] 375 FM Memorex 651 single 64 32 1.056 b:

  9. Orders of magnitude (length) - Wikipedia

    en.wikipedia.org/wiki/Orders_of_magnitude_(length)

    Maximum diameter of Thiomargarita namibiensis, the second largest bacterium ever discovered 10 −3: 1 millimeter ~5 mm Length of an average flea is 1–10 mm (usually <5 mm) [27] 2.54 mm One-tenth inch; distance between pins in DIP (dual-inline-package) electronic components 5.70 mm Diameter of the projectile in 5.56×45mm NATO ammunition 10 −2