When.com Web Search

  1. Ad

    related to: 3.5 cm to inches calculator 8 bit

Search results

  1. Results From The WOW.Com Content Network
  2. Minifloat - Wikipedia

    en.wikipedia.org/wiki/Minifloat

    A minifloat in 1 byte (8 bit) with 1 sign bit, 4 exponent bits and 3 significand bits (in short, a 1.4.3 minifloat) is demonstrated here. The exponent bias is defined as 7 to center the values around 1 to match other IEEE 754 floats [3] [4] so (for most values) the actual multiplier for exponent x is 2 x−7. All IEEE 754 principles should be ...

  3. HP Prime - Wikipedia

    en.wikipedia.org/wiki/HP_Prime

    18.23×8.58×1.39 cm (7.13×3.38×0.550 inches) [5] The HP Prime Graphing Calculator is a graphing calculator introduced by Hewlett-Packard in 2013 and manufactured by HP Inc. until the licensees Moravia Consulting spol. s r.o. and Royal Consumer Information Products, Inc. took over the continued development, manufacturing, distribution ...

  4. TI-Nspire series - Wikipedia

    en.wikipedia.org/wiki/TI-Nspire_series

    The original TI-Nspire was developed out of the TI PLT SHH1 prototype calculator, the TI-92 series of calculators released in 1995, and the TI-89 series of calculators released in 1998. [ 2 ] [ 3 ] In 2011, Texas Instruments released the CX line of their TI-Nspire calculators which effectively replaced the previous generation.

  5. List of humorous units of measurement - Wikipedia

    en.wikipedia.org/wiki/List_of_humorous_units_of...

    At the time, Smoot was 5 feet, 7 inches, or 170 cm, tall. [18] Google Earth and Google Calculator include the smoot as a unit of measurement. The Cambridge (Massachusetts) police department adopted the convention of using Smoots to measure the locations of accidents and incidents on the bridge.

  6. List of drill and tap sizes - Wikipedia

    en.wikipedia.org/wiki/List_of_drill_and_tap_sizes

    Example (inch, coarse): For size 7 ⁄ 16 (this is the diameter of the intended screw in fraction form)-14 (this is the number of threads per inch; 14 is considered coarse), 0.437 in × 0.85 = 0.371 in. Therefore, a size 7 ⁄ 16 screw (7 ⁄ 16 ≈ 0.437) with 14 threads per inch (coarse) needs a tap drill with a diameter of about 0.371 inches.

  7. Display size - Wikipedia

    en.wikipedia.org/wiki/Display_size

    The size of a screen is usually described by the length of its diagonal, which is the distance between opposite corners, typically measured in inches. It is also sometimes called the physical image size to distinguish it from the "logical image size," which describes a screen's display resolution and is measured in pixels .

  8. Drive bay - Wikipedia

    en.wikipedia.org/wiki/Drive_bay

    They were 3 + 1 ⁄ 4 inches (82.6 mm) high, 5 + 3 ⁄ 4 inches (146.1 mm) wide, and up to 8 inches (203.2 mm) deep, used mainly for hard disk drives and floppy disk drives. This is the size of the internal (screwed) part of the bay, as the front side is actually 5 + 7 ⁄ 8 inches (149.2 mm). The difference between those widths and the name of ...

  9. Programmable calculator - Wikipedia

    en.wikipedia.org/wiki/Programmable_calculator

    The earlier programmable calculators, as well as the pocket computers mentioned above, also had such things as video interfaces for televisions and composite monitors, 2½ inch mini floppy disc drives, bar-code readers, and standard RS-232 connectivity which provided for other such things as modems, external hard drives and more. The printer ...