When.com Web Search

Search results

  1. Results From The WOW.Com Content Network
  2. Mass fraction (chemistry) - Wikipedia

    en.wikipedia.org/wiki/Mass_fraction_(chemistry)

    Mass fraction can also be expressed, with a denominator of 100, as percentage by mass (in commercial contexts often called percentage by weight, abbreviated wt.% or % w/w; see mass versus weight). It is one way of expressing the composition of a mixture in a dimensionless size ; mole fraction (percentage by moles , mol%) and volume fraction ...

  3. Parts-per notation - Wikipedia

    en.wikipedia.org/wiki/Parts-per_notation

    At 1 ppm the solution is a very pale yellow. As the concentration increases the colour becomes a more vibrant yellow, then orange, with the final 10,000 ppm a deep red colour. In science and engineering , the parts-per notation is a set of pseudo-units to describe small values of miscellaneous dimensionless quantities , e.g. mole fraction or ...

  4. Useful conversions and formulas for air dispersion modeling

    en.wikipedia.org/wiki/Useful_conversions_and...

    Here are the conversion factors for those various expressions of wind speed: 1 m/s = 2.237 statute mile/h = 1.944 knots 1 knot = 1.151 statute mile/h = 0.514 m/s 1 statute mile/h = 0.869 knots = 0.447 m/s. Note: 1 statute mile = 5,280 feet = 1,609 meters

  5. Air pollutant concentrations - Wikipedia

    en.wikipedia.org/wiki/Air_pollutant_concentrations

    This article presents methods for converting concentrations from ppmv to mg/m 3 (and vice versa) and for correcting the concentrations to the required reference conditions. All of the concentrations and concentration corrections in this article apply only to air and other gases. They are not applicable for liquids.

  6. Total dissolved solids - Wikipedia

    en.wikipedia.org/wiki/Total_dissolved_solids

    where TDS is expressed in mg/L and EC is the electrical conductivity in microsiemens per centimeter at 25 °C. The conversion factor k e varies between 0.55 and 0.8. [5] Some TDS meters use an electrical conductivity measurement to the ppm using the above formula. Regarding units, 1 ppm indicates 1 mg of dissolved solids per 1,000 g of water. [6]

  7. Talk:Parts-per notation - Wikipedia

    en.wikipedia.org/wiki/Talk:Parts-per_notation

    The examples don't seem to be too accurate. A drop is usually defined as 0.05 ml, which then gives;. 1 drop in 50 ml = 1‰, 50ml is a very small cup 1 drop in 50 l = 1ppm 50 l is about 11 gallons, not 40 1 drop in 50 cubic metres = 1 ppb 1 drop = 1ppt, a 50 m swimming pool is 50*25*2 = 2,500 m^3 1 drop in 50,000,000 cubic metres = 1ppq, 50,000,000 m^3 is equivalent to a lake covering a square ...

  8. Per mille - Wikipedia

    en.wikipedia.org/wiki/Per_mille

    Visualisation of 1%, 1‰, 1‱, 1 pcm and 1 ppm as fractions of the large block . Percentage point difference of 1 part in 100; Percentage (%) 1 part in 100; Basis point (bp) difference of 1 part in 10,000; Permyriad (‱) 1 part in 10,000; Per cent mille (pcm) 1 part in 100,000

  9. Percentage solution - Wikipedia

    en.wikipedia.org/wiki/Percentage_solution

    Mass fraction (or "% w/w" or "wt.%"), for percent mass; Volume fraction (or "% v/v" or "vol.%"), volume concentration, for percent volume "Mass/volume percentage" (or "% m/v") in biology, for mass per unit volume; incorrectly used to denote mass concentration (chemistry). See usage in biology