When.com Web Search

  1. Ad

    related to: cobra jet intake manifold dyno chart results

Search results

  1. Results From The WOW.Com Content Network
  2. Ford Modular engine - Wikipedia

    en.wikipedia.org/wiki/Ford_Modular_engine

    The Aluminator 5.2 XS is another variant of the Coyote engine utilizing the 5.2 L cylinder block from the GT350. The Aluminator is differentiated from the Voodoo engine by a Cobra Jet intake manifold and throttle body and a cross-plane crankshaft. [47] The engine has a claimed output of 580 hp (433 kW) and 445 lb⋅ft (603 N⋅m).

  3. Ford FE engine - Wikipedia

    en.wikipedia.org/wiki/Ford_FE_engine

    The 428 Cobra Jet was a performance version of the 428 FE. Launched in April 1968, it was built on a regular production line using a variety of cylinder heads [30] combined with a 735 CFM Holley four-barrel carburetor. The Cobra Jet used heavier connecting rods with a 13/32 rod bolt and a nodular iron crankshaft casting #1UB.

  4. Ford Mustang SVT Cobra - Wikipedia

    en.wikipedia.org/wiki/Ford_Mustang_SVT_Cobra

    The 1994 Cobra was introduced midway through the model year with the same engine as the 1993 Cobra. With its GT-40 cast-iron heads and lower intake and its Cobra-specific upper intake, [1]: 36 power increased to 240 hp (179 kW; 243 PS). [1]: 34 However, the actual output of the Cobra's GT-40 enhanced engine was probably higher.

  5. Boss 429 Mustang - Wikipedia

    en.wikipedia.org/wiki/Boss_429_Mustang

    The Mustang's engine compartment was not wide enough to accommodate the massive Boss 429 engine, so Ford contracted with Kar Kraft of Dearborn, Michigan, to modify 4-speed Cobra Jet Mustangs to accept it. Kar Kraft was a Ford exclusive experimental facility that functioned as Vehicle Engineering for Ford's Special Vehicles.

  6. Ford 385 engine - Wikipedia

    en.wikipedia.org/wiki/Ford_385_engine

    Ford developed two high-performance street versions of the 429 between 1969 and 1971, the Cobra Jet and Super Cobra Jet. The Cobra Jet (429CJ) was fitted with a Rochester Quadrajet 715 cu ft/min (20.2 m 3 /min) Spreadbore 4-bbl carburetor, a larger camshaft; a special set of cylinder heads (DOOE-R) 73.5 CC, combustion chamber and canted valve ...

  7. Inlet manifold - Wikipedia

    en.wikipedia.org/wiki/Inlet_manifold

    An inlet manifold or intake manifold (in American English) is the part of an internal combustion engine that supplies the fuel/air mixture to the cylinders. [1] The word manifold comes from the Old English word manigfeald (from the Anglo-Saxon manig [many] and feald [repeatedly]) and refers to the multiplying of one (pipe) into many.

  8. Components of jet engines - Wikipedia

    en.wikipedia.org/wiki/Components_of_jet_engines

    Diagram of a typical gas turbine jet engine. Air is compressed by the compressor blades as it enters the engine, and it is mixed and burned with fuel in the combustion section. The hot exhaust gases provide forward thrust and turn the turbines which drive the compressor blades. 1. Intake 2. Low pressure compression 3. High pressure compression ...

  9. Ford 335 engine - Wikipedia

    en.wikipedia.org/wiki/Ford_335_engine

    The Q-code 351 "Cobra-Jet" (also called 351-CJ, 351-4V) was produced from May 1971 through the 1974 model year. It was a lower-compression design that used open-chamber 4V heads. [ 5 ] The open-chamber heads exhibited superior emissions characteristics and were used to meet the more stringent emissions standards for 1972 and beyond. [ 1 ]