Ad
related to: 3 8 inches to mm
Search results
Results From The WOW.Com Content Network
Nominal Pipe Size (NPS) is a North American set of standard sizes for pipes used for high or low pressures and temperatures. [1] " Nominal" refers to pipe in non-specific terms and identifies the diameter of the hole with a non-dimensional number (for example – 2-inch nominal steel pipe" consists of many varieties of steel pipe with the only criterion being a 2.375-inch (60.3 mm) outside ...
The Charrière is measured by the ''outer'' diameter, and is defined as 1 Fr = 1/3 mm, and thus 1 mm = 3 Fr; therefore the diameter of a round catheter in millimetres can be determined by dividing the French size by 3. [2] The French units roughly correspond to the outer circumference of the catheter (see table below).
3 + 5 ⁄ 8 inches (92 mm) 3 + 13 ⁄ 16 inches (97 mm) 4 inches (102 mm) 4 + 3 ⁄ 16 inches (106 mm) 9 + 1 ⁄ 3 inches (237 mm) 6 + 17 ⁄ 25 inches (170 mm) 2 + 3 ⁄ 8 inches (60 mm) 2 + 9 ⁄ 16 inches (65 mm) 2 + 3 ⁄ 4 inches (70 mm) 2 + 15 ⁄ 16 inches (75 mm) 3 + 1 ⁄ 8 inches (79 mm) 3 + 5 ⁄ 16 inches (84 mm) 3 + 1 ⁄ 2 inches ...
The millimetre (SI symbol: mm) is a unit of length in the metric system equal to 10 −3 metres ( 1 / 1 000 m = 0.001 m). To help compare different orders of magnitude , this section lists lengths between 10 −3 m and 10 −2 m (1 mm and 1 cm).
Converts measurements to other units. Template parameters [Edit template data] This template prefers inline formatting of parameters. Parameter Description Type Status Value 1 The value to convert. Number required From unit 2 The unit for the provided value. Suggested values km2 m2 cm2 mm2 ha sqmi acre sqyd sqft sqin km m cm mm mi yd ft in kg g mg lb oz m/s km/h mph K C F m3 cm3 mm3 L mL cuft ...
Subdivisions of an inch are typically written using dyadic fractions with odd number numerators; for example, two and three-eighths of an inch would be written as 2 + 3 / 8 ″ and not as 2.375″ nor as 2 + 6 / 16 ″. However, for engineering purposes fractions are commonly given to three or four places of decimals and have been ...
Rear axle 3 ⁄ 8 inch (9.53 mm) diameter, 26 tpi GB Stems using 5 ⁄ 16 inch (7.94 mm) diameter, 26 tpi for the handlebar clamp Note that M8 × 1.00 metric threaded parts can interchange with 5 ⁄ 16 inch (7.94 mm) diameter × 26 tpi parts with a " Class B fit ", meaning you should not go back and forth between threadings.
They are typically about 1 inch (25 mm) long. For example, a 1 ⁄ 4-inch to 3 ⁄ 8-inch adapter allows sockets with 1 ⁄ 4-inch drive holes to attach to a 3 ⁄ 8-inch ratchet, and so on. Universal joints are two articulated socket joints (about 1 inch (25 mm) long) combined at a right angle, that allow a bend in the turning axis of the ...