When.com Web Search

Search results

1. Results From The WOW.Com Content Network

2. Width across flats - Wikipedia

   en.wikipedia.org/wiki/Width_across_flats

   A few sizes are close enough to interchange for most purposes, such as 19 mm (close to 3 ⁄ 4 inch (19.05 mm)), 8 mm (close to 5 ⁄ 16 inch (7.94 mm)) and 4 mm (close to 5 ⁄ 32 inch (3.97 mm)). In reality, a wrench with a width across the flats of exactly 15 mm would fit too tightly to use on a bolt with a width across the flats of 15 mm.

3. ISO metric screw thread - Wikipedia

   en.wikipedia.org/wiki/ISO_metric_screw_thread

   Below are some common spanner sizes for metric screw threads. Hexagonal (generally abbreviated to "hex") head widths (width across flats, spanner size) are for DIN 934 hex nuts and hex head bolts. Other (usually smaller) sizes may occur to reduce weight or cost, including the small series flange bolts defined in ISO 4162 which typically have ...

4. List of thread standards - Wikipedia

   en.wikipedia.org/wiki/List_of_thread_standards

   ISO general purpose metric screw threads—General plan: V Thread Form: M6x1 ISO 262:1998: ISO general purpose metric screw threads—Selected sizes for screws, bolts and nuts: V Thread Form ISO 724:1993: ISO general-purpose metric screw threads—Basic dimensions: V Thread Form ISO 725:2009: ISO inch screw threads—Basic dimensions: V Thread ...

5. British Association screw threads - Wikipedia

   en.wikipedia.org/wiki/British_Association_screw...

   The major diameter is given by 6p 1.2, [4]: 12 rounded to two significant figures in mm and the hex head size (across the flats) is 1.75 times the major diameter. BA sizes are specified by the following British Standards: BS 57:1951 — B.A. screws, bolts and nuts

6. List of screw and bolt types - Wikipedia

   en.wikipedia.org/wiki/List_of_screw_and_bolt_types

   In 1913, Woolley and Meredith defined them like Anthony, but gave the following dimensions: hex head cap screws up to and including 7 ⁄ 16 inch (11.1125 mm) have a head that is 3 ⁄ 16 inch (4.7625 mm) larger than the shank diameter; screws greater than 1 ⁄ 2 inch (12.7 mm) in diameter have a head that is 1 ⁄ 4 inch (6.35 mm) larger than ...

7. Unified Thread Standard - Wikipedia

   en.wikipedia.org/wiki/Unified_Thread_Standard

   Even though #14 and #16 screws are still available, they are not as common as sizes #0 through #12. [citation needed] Sometimes "special" diameter and pitch combinations (UNS) are used, for example a 0.619 in (15.7 mm) major diameter with 20 threads per inch. UNS threads are rarely used for bolts, but rather on nuts, tapped holes, and threaded ODs.

8. AOL Mail is free and helps keep you safe.

   mail.aol.com/?icid=aol.com-nav

   Get AOL Mail for FREE! Manage your email like never before with travel, photo & document views. Personalize your inbox with themes & tabs. You've Got Mail!

9. British Standard Whitworth - Wikipedia

   en.wikipedia.org/wiki/British_Standard_Whitworth

   To simplify matters, the term hexagon is used in this section to denote either bolt head or nut. Two spanners, both nominal size 5 ⁄ 8 in, with a diagram superimposed to show the logic that allows them both to be nominal size 5 ⁄ 8 in when their actual sizes are clearly different (across-flats distance vs screw diameter). The across-flats ...