When.com Web Search

  1. Ads

    related to: nut bolt size chart in mm pdf free download 336 pages

Search results

  1. Results From The WOW.Com Content Network
  2. Width across flats - Wikipedia

    en.wikipedia.org/wiki/Width_across_flats

    A few sizes are close enough to interchange for most purposes, such as 19 mm (close to 3 ⁄ 4 inch (19.05 mm)), 8 mm (close to 5 ⁄ 16 inch (7.94 mm)) and 4 mm (close to 5 ⁄ 32 inch (3.97 mm)). In reality, a wrench with a width across the flats of exactly 15 mm would fit too tightly to use on a bolt with a width across the flats of 15 mm.

  3. ISO metric screw thread - Wikipedia

    en.wikipedia.org/wiki/ISO_metric_screw_thread

    Below are some common spanner sizes for metric screw threads. Hexagonal (generally abbreviated to "hex") head widths (width across flats, spanner size) are for DIN 934 hex nuts and hex head bolts. Other (usually smaller) sizes may occur to reduce weight or cost, including the small series flange bolts defined in ISO 4162 which typically have ...

  4. List of screw and bolt types - Wikipedia

    en.wikipedia.org/wiki/List_of_screw_and_bolt_types

    In 1913, Woolley and Meredith defined them like Anthony, but gave the following dimensions: hex head cap screws up to and including 7 ⁄ 16 inch (11.1125 mm) have a head that is 3 ⁄ 16 inch (4.7625 mm) larger than the shank diameter; screws greater than 1 ⁄ 2 inch (12.7 mm) in diameter have a head that is 1 ⁄ 4 inch (6.35 mm) larger than ...

  5. British Association screw threads - Wikipedia

    en.wikipedia.org/wiki/British_Association_screw...

    The major diameter is given by 6p 1.2, [4]: 12 rounded to two significant figures in mm and the hex head size (across the flats) is 1.75 times the major diameter. BA sizes are specified by the following British Standards: BS 57:1951 — B.A. screws, bolts and nuts

  6. Unified Thread Standard - Wikipedia

    en.wikipedia.org/wiki/Unified_Thread_Standard

    Even though #14 and #16 screws are still available, they are not as common as sizes #0 through #12. [citation needed] Sometimes "special" diameter and pitch combinations (UNS) are used, for example a 0.619 in (15.7 mm) major diameter with 20 threads per inch. UNS threads are rarely used for bolts, but rather on nuts, tapped holes, and threaded ODs.

  7. British Standard Whitworth - Wikipedia

    en.wikipedia.org/wiki/British_Standard_Whitworth

    To simplify matters, the term hexagon is used in this section to denote either bolt head or nut. Two spanners, both nominal size 5 ⁄ 8 in, with a diagram superimposed to show the logic that allows them both to be nominal size 5 ⁄ 8 in when their actual sizes are clearly different (across-flats distance vs screw diameter). The across-flats ...

  8. ISO 898 - Wikipedia

    en.wikipedia.org/wiki/ISO_898

    This standard is the origin for other standards that define properties for similar metric fasteners, such as SAE J1199 and ASTM F568M. [1] It is divided into five (nonconsecutive) parts: 1. Bolts, screws and studs with specified property classes – Coarse thread and fine pitch thread [2] 2. Nuts with specified proof load values – Coarse ...

  9. British Standard Fine - Wikipedia

    en.wikipedia.org/wiki/British_Standard_Fine

    British Standard Fine (BSF) is a screw thread form, as a fine-pitch alternative to British Standard Whitworth (BSW) thread. It was used for steel bolts and nuts on and in much of Britain's machinery, including cars, prior to adoption of Unified, and later Metric, standards.