When.com Web Search

  1. Ads

    related to: inch fraction to decimal table

Search results

  1. Results From The WOW.Com Content Network
  2. Drill bit sizes - Wikipedia

    en.wikipedia.org/wiki/Drill_bit_sizes

    So, instead of 78/64 inch, or 1 14/64 inch, the size is noted as 1 7/32 inch. Below is a chart providing the decimal-fraction equivalents that are most relevant to fractional-inch drill bit sizes (that is, 0 to 1 by 64ths). (Decimal places for .25, .5, and .75 are shown to thousandths [.250, .500, .750], which is how machinists usually think ...

  3. List of drill and tap sizes - Wikipedia

    en.wikipedia.org/wiki/List_of_drill_and_tap_sizes

    The major minus pitch technique also works for inch-based threads, but you must first calculate the pitch by converting the fraction of threads-per-inch (TPI) into a decimal. For example, a screw with a pitch of 1/20 in (20 threads per inch) has a pitch of 0.050 in and a 1 ⁄ 13 in pitch (13 threads per inch) has a pitch of 0.077 in.

  4. Inch - Wikipedia

    en.wikipedia.org/wiki/Inch

    Subdivisions of an inch are typically written using dyadic fractions with odd number numerators; for example, two and three-eighths of an inch would be written as ⁠2 + 3 / 8 ⁠ ″ and not as 2.375″ nor as ⁠2 + 6 / 16 ⁠ ″. However, for engineering purposes fractions are commonly given to three or four places of decimals and have been ...

  5. File:Decimal-fraction equivalents--v0006.svg - Wikipedia

    en.wikipedia.org/wiki/File:Decimal-fraction...

    A handy chart of decimal-fraction equivalents, 0 to 1 by 64ths. Prints nicely as 11x17 in landscape orientation. Useful for machinists who work with inch-based measurements. Date: 24 October 2007: Source: Own work: Author: Three-quarter-ten

  6. Wrench size - Wikipedia

    en.wikipedia.org/wiki/Wrench_size

    Sizes that may interchange, depending on the precision needed, include 2 mm (close to 5 ⁄ 64 inch (1.98 mm)), 4 mm (close to 5 ⁄ 32 inch (3.97 mm)) and 8 mm (close to 5 ⁄ 16 inch (7.94 mm)). In reality, a wrench with a width across the flats of exactly 15 mm would fit too tightly to use on a bolt with a width across the flats of 15 mm.

  7. Gauge (firearms) - Wikipedia

    en.wikipedia.org/wiki/Gauge_(firearms)

    Note: Use of this table for estimating bullet masses for historical large-bore rifles is limited, as this table assumes the use of round ball, rather than conical bullets; for example, a typical 4-bore rifle from circa 1880 used a 2,000-grain (4.57 oz; 129.60 g) bullet, or sometimes slightly heavier, rather than using a 4-ounce (110 g) round ...

  8. Remove Banner Ads with Ad-Free AOL Mail | AOL Products

    www.aol.com/products/utilities/ad-free-mail

    Ad-Free AOL Mail offers you the AOL webmail experience minus paid ads, allowing you to focus on your inbox without distractions, for just $4.99 per month.

  9. Fraction - Wikipedia

    en.wikipedia.org/wiki/Fraction

    To change ⁠ 1 / 3 ⁠ to a decimal, divide 1.000... by 3 (" 3 into 1.000... "), and stop when the desired accuracy is obtained, e.g., at 4 decimals with 0.3333. The fraction ⁠ 1 / 4 ⁠ can be written exactly with two decimal digits, while the fraction ⁠ 1 / 3 ⁠ cannot be written exactly as a