Ad
related to: 5/16 inch to mm
Search results
Results From The WOW.Com Content Network
Example (metric, fine): For M7.0 × 0.5, 7.0 − 0.5 = 6.5 (The 85% coarse, 90% fine guideline, within its effective range, matches this in net effect) The major minus pitch also works for inch-based threads, but you must first determine the pitch by looking at the number of treads per inch (TPI; for example, 1 ⁄ 20 = 0.050 and 1 ⁄ 13 ≈ 0 ...
A few sizes are close enough to interchange for most purposes, such as 19 mm (close to 3 ⁄ 4 inch (19.05 mm)), 8 mm (close to 5 ⁄ 16 inch (7.94 mm)) and 4 mm (close to 5 ⁄ 32 inch (3.97 mm)). In reality, a wrench with a width across the flats of exactly 15 mm would fit too tightly to use on a bolt with a width across the flats of 15 mm.
For Morse taper-shank drill bits, the standard continues in 1/64 inch increments up to 1¾ inch, then 1/32 inch increments up to 2¼ inch, 1/16 inch increments up to 3 inches, 1/8 inch increments up to 3¼ inches, and a single 1/4 inch increment to 3½ inches. One aspect of this method of sizing is that the size increment between drill bits ...
Nominal Pipe Size (NPS) is a North American set of standard sizes for pipes used for high or low pressures and temperatures. [1] " Nominal" refers to pipe in non-specific terms and identifies the diameter of the hole with a non-dimensional number (for example – 2-inch nominal steel pipe" consists of many varieties of steel pipe with the only criterion being a 2.375-inch (60.3 mm) outside ...
The standard designation for a UTS thread is a number indicating the nominal (major) diameter of the thread, followed by the pitch measured in threads per inch.For diameters smaller than 1 / 4 inch, the diameter is indicated by an integer number defined in the standard; for all other diameters, the inch figure is given.
Used for 12 mm, and 12.5 mm figure scale miniature wargaming. 1:128: 3 ⁄ 32 in: 2.381 mm A few rockets and some fit-in-the-box aircraft are made to this size. 1:120: 0.1 in: 2.54 mm: Model railways (TT) Derived from the scale of 1 inch equals 10 feet.TT model railroad scale. Used in AD&D Battlesystem Skirmishes rules. Works with 15 mm ...
1.0 mm – 0.03937 inches or 5/127 (exactly) 1.0 mm – side of a square of area 1 mm²; 1.0 mm – diameter of a pinhead; 1.5 mm – average length of a flea [27] 2.54 mm – distance between pins on old dual in-line package (DIP) electronic components; 5 mm – length of an average red ant; 5 mm – diameter of an average grain of rice
≈ 16.933 mm: Four-line Pica French canon Canon Gros-canon [f] Kleine Missal: Konkordanz Kleine missaal 54 ≈ 19.050 mm: Missal: Missaal 56 ≈ 19.756 mm: Double-canon 60 ≈ 21.167 mm: Five-line pica: Große Missal: Sabon 66 ≈ 23.283 mm: Große Sabon [8] Grote sabon 72 25.4 mm: Six-line pica Inch: Double-trismégiste: Sabon Sechscicero [8 ...