When.com Web Search

  1. Ads

    related to: 1 inch brass compression fittings

Search results

  1. Results From The WOW.Com Content Network
  2. Compression fitting - Wikipedia

    en.wikipedia.org/wiki/Compression_fitting

    A compression fitting 15 mm isolating valve. A compression fitting is a fitting used in plumbing and electrical conduit systems to join two tubes or thin-walled pipes together. . In instances where two pipes made of dissimilar materials are to be joined (most commonly PVC and copper), the fittings will be made of one or more compatible materials appropriate for the connect

  3. Piping and plumbing fitting - Wikipedia

    en.wikipedia.org/wiki/Piping_and_plumbing_fitting

    Push-to-pull fittings are easily removed compression fitting that allows pipes to be connected with minimal tools. These fittings are similar to regular compression fittings but use an O-ring for sealing and a grip ring to hold the pipe. The main advantage is that it can easily be removed and re-used, it is easy to assemble, and the joints are ...

  4. National pipe thread - Wikipedia

    en.wikipedia.org/wiki/National_pipe_thread

    The taper rate for all NPT threads is 1 inch of diameter in 16 inches of length (3 ⁄ 4 inch per foot or 62.5 millimeters per meter) measured by the change of diameter (of the pipe thread) over distance of thread. The half-angle (between the taper surface and the axis of the pipe) is arctan(1 ⁄ 32) ≈ 1.7899° ≈ 1° 47′.

  5. Copper tubing - Wikipedia

    en.wikipedia.org/wiki/Copper_tubing

    Generally, copper tubes are soldered directly into copper or brass fittings, although compression, crimp, or flare fittings are also used. Formerly, concerns with copper supply tubes included the lead used in the solder at joints (50% tin and 50% lead). Some studies have shown significant leaching of the lead into the potable water stream ...

  6. Nipple (plumbing) - Wikipedia

    en.wikipedia.org/wiki/Nipple_(plumbing)

    ASTM B687-99(2005)e1 Standard Specification for Brass, Copper, and Chromium-Plated Pipe Nipples. ASME B1.20.7 Hose Coupling Screw Threads, Inch. (Quote: The normal sequence of connections, in relation to the direction of flow, is from an externally threaded nipple into an internally threaded coupling)

  7. JIC fitting - Wikipedia

    en.wikipedia.org/wiki/JIC_fitting

    JIC fittings, defined by the SAE J514 and MIL-DTL-18866 standards, are a type of flare fitting machined with a 37-degree flare seating surface. JIC (Joint Industry Council) fittings are widely used in fuel delivery and fluid power applications, especially where high pressure (up to 10,000 pounds per square inch (690 bar)) is involved.

  8. Flare fitting - Wikipedia

    en.wikipedia.org/wiki/Flare_fitting

    Flared fittings are an alternative to solder-type joints that are mechanically separable and doesn’t require an open flame. Copper tube used for propane, liquefied petroleum gas, or natural gas may use flared brass fittings of single 45°-flare type, according to NFPA 54/ANSI. Z223.1 National Fuel Gas Code.

  9. Pipe (fluid conveyance) - Wikipedia

    en.wikipedia.org/wiki/Pipe_(fluid_conveyance)

    Consequently, a 1-inch (25 mm) copper pipe had a 1 + 1 ⁄ 8-inch (28.58 mm) outside diameter. The outside diameter was the important dimension for mating with fittings. The wall thickness on modern copper is usually thinner than 1 ⁄ 16-inch (1.6 mm), so the internal diameter is only "nominal" rather than a controlling dimension. [13]

  1. Ads

    related to: 1 inch brass compression fittings