When.com Web Search

  1. Ads

    related to: ppr pipe size in mm

Search results

  1. Results From The WOW.Com Content Network
  2. Nominal Pipe Size - Wikipedia

    en.wikipedia.org/wiki/Nominal_Pipe_Size

    Nominal Pipe Size (NPS) is a North American set of standard sizes for pipes used for high or low pressures and temperatures. [1] " Nominal" refers to pipe in non-specific terms and identifies the diameter of the hole with a non-dimensional number (for example – 2-inch nominal steel pipe" consists of many varieties of steel pipe with the only criterion being a 2.375-inch (60.3 mm) outside ...

  3. British Standard Pipe - Wikipedia

    en.wikipedia.org/wiki/British_Standard_Pipe

    the thread size; Threads are normally right-hand. For left-hand threads, the letters, LH, are appended. Example: Pipe thread EN 10226 Rp 2 + 1 ⁄ 2. The terminology for the use of G and R originated from Germany (G for gas, as it was originally designed for use on gas pipes; R for rohr, meaning pipe.)

  4. Plastic pipework - Wikipedia

    en.wikipedia.org/wiki/Plastic_pipework

    Pipes, fittings, valves, and accessories make up a plastic pressure pipe system. The range of pipe diameters for each pipe system does vary. However, the size ranges from 12 to 400 mm (0.472 to 15.748 in) and 3 ⁄ 8 to 16 in (9.53 to 406.40 mm). Pipes are extruded and are generally available in: 3 m (9.84 ft), 4 m (13.12 ft), 5 m (16.40 ft ...

  5. Tube (fluid conveyance) - Wikipedia

    en.wikipedia.org/wiki/Tube_(fluid_conveyance)

    A tube and pipe may be specified by standard pipe size designations, e.g., nominal pipe size, or by nominal outside or inside diameter and/or wall thickness. The actual dimensions of pipe are usually not the nominal dimensions: A 1-inch pipe will not actually measure 1 inch in either outside or inside diameter, whereas many types of tubing are ...

  6. Copper tubing - Wikipedia

    en.wikipedia.org/wiki/Copper_tubing

    For example, DN20 is the size for copper pipe with an outside diameter of 19.05 mm or 3 ⁄ 4 inch. While pipe sizes in Australia are inch-based, they are classified by outside rather than inside diameter (e.g., a nominal 3 ⁄ 4 inch copper pipe in Australia has measured diameters of 0.750 inches outside and 0.638 inches inside, whereas a ...

  7. Piping and plumbing fitting - Wikipedia

    en.wikipedia.org/wiki/Piping_and_plumbing_fitting

    A reducer reduces the pipe size from a larger to a smaller bore (inner diameter). Alternatively, reducer may refer to any fitting which causes a change in pipe diameter. [15] This change may be intended to meet hydraulic flow requirements of the system or adapt to existing piping of a different size. The reduction length is usually equal to the ...

  8. Standard dimension ratio - Wikipedia

    en.wikipedia.org/wiki/Standard_dimension_ratio

    Standard dimension ratio (SDR) is a method of rating a pipe's durability against pressure. The standard dimension ratio describes the correlation between the pipe dimension and the thickness of the pipe wall. [1] Common nominations are SDR11, SDR17, SDR26 and SDR35. Pipes with a lower SDR can withstand higher pressures.

  9. Iron pipe size - Wikipedia

    en.wikipedia.org/wiki/Iron_pipe_size

    During the IPS period, pipes were cast in halves and welded together, and pipe sizes referred to the inside diameters. [1] The inside diameters under IPS were roughly the same as the more modern Ductile Iron Pipe Standard (DIPS) and Nominal Pipe Size (NPS) Standards, and some of the wall thicknesses were also retained with a different ...