When.com Web Search

Search results

  1. Results From The WOW.Com Content Network
  2. Useful conversions and formulas for air dispersion modeling

    en.wikipedia.org/wiki/Useful_conversions_and...

    For example, such a regulation might limit the concentration of NOx to 55 ppmv in a dry combustion exhaust gas corrected to 3 volume percent O 2. As another example, a regulation might limit the concentration of particulate matter to 0.1 grain per standard cubic foot (i.e., scf) of dry exhaust gas corrected to 12 volume percent CO 2.

  3. Air pollutant concentrations - Wikipedia

    en.wikipedia.org/wiki/Air_pollutant_concentrations

    As an example, a measured NO x concentration of 45 ppmv in a dry gas having 5 volume % O 2 is: 45 × ( 20.9 - 3 ) ÷ ( 20.9 - 5 ) = 50.7 ppmv of NO x. when corrected to a dry gas having a specified reference O 2 content of 3 volume %. Note: The measured gas concentration C m must first be corrected to a dry basis before using the above equation.

  4. Parts-per notation - Wikipedia

    en.wikipedia.org/wiki/Parts-per_notation

    At 1 ppm the solution is a very pale yellow. As the concentration increases the colour becomes a more vibrant yellow, then orange, with the final 10,000 ppm a deep red colour. In science and engineering , the parts-per notation is a set of pseudo-units to describe small values of miscellaneous dimensionless quantities , e.g. mole fraction or ...

  5. Total dissolved solids - Wikipedia

    en.wikipedia.org/wiki/Total_dissolved_solids

    where TDS is expressed in mg/L and EC is the electrical conductivity in microsiemens per centimeter at 25 °C. The conversion factor k e varies between 0.55 and 0.8. [5] Some TDS meters use an electrical conductivity measurement to the ppm using the above formula. Regarding units, 1 ppm indicates 1 mg of dissolved solids per 1,000 g of water. [6]

  6. Mass fraction (chemistry) - Wikipedia

    en.wikipedia.org/wiki/Mass_fraction_(chemistry)

    Instead, the concentration should simply be given in units of g/mL. Percent solution or percentage solution are thus terms best reserved for mass percent solutions (m/m, m%, or mass solute/mass total solution after mixing), or volume percent solutions (v/v, v%, or volume solute per volume of total solution after mixing).

  7. Molar concentration - Wikipedia

    en.wikipedia.org/wiki/Molar_concentration

    The concentration of pure osmium tetroxide (molar mass = 254.23 g/mol) is c(OsO 4) = ⁠ 5.1 kg/L / 254.23 g/mol ⁠ = 20.1 mol/L. A typical protein in bacteria, such as E. coli, may have about 60 copies, and the volume of a bacterium is about 10 −15 L. Thus, the number concentration C is C = 60 / (10 −15 L) = 6 × 10 16 L −1. The molar ...

  8. What Is The Difference Between A Celery Stalk And A ... - AOL

    www.aol.com/difference-between-celery-stalk...

    What Is A Celery Rib? A celery rib is one of the individual stems that make up the larger bunch of celery, or "stalk." In botanical terms, a rib is a single segment of the plant, and in culinary ...

  9. Conversion of units - Wikipedia

    en.wikipedia.org/wiki/Conversion_of_units

    As a more complex example, the concentration of nitrogen oxides (NO x) in the flue gas from an industrial furnace can be converted to a mass flow rate expressed in grams per hour (g/h) of NO x by using the following information as shown below: NO x concentration = 10 parts per million by volume = 10 ppmv = 10 volumes/10 6 volumes NO x molar mass